Fedora Core 11 live screenshot

Managed to download a 689Mb

[namran@nb-namran iso]$ ll -h Fedora-11-i686-Live.iso 
-rw-rw-r-- 1 namran namran 689M Jun 10 18:49 Fedora-11-i686-Live.iso

The live iso was downloaded from a japan mirror.
fc11-download-speed
and also

[root@fedora fc11]# ll -h
total 3.5G
-rw-rw-r-- 1 namran namran 3.5G Jun 11 18:33 Fedora-11-i386-DVD.iso

the ISO for 3.5Gb DVD image was downloaded from UPM mirror.. i think..

the screenshot of FC11 live is as below, as never had chance to install FC11 full yet.

The login screen :

FC 11 live login screen
FC 11 live login screen

The Desktop of FC 11 screen:
fc11-live-user.jpg

The bunch of application filed under “Internet section” :
fc11-internet.jpg

Pidgin and Firefox..
fc11-pidgin.jpg

Hmm.. i was trying to install it into Hardisk.. was it was uncompleted forever.. somesort of “BSOD” but instead of blue screen..
it got a spinning spinning icon which took forever to complete…

p/s : One comment though.. I still prefer the artwork of FC10 instead of the FC11.. hehehehe 😎

More for a bunch of screenshot during my attempt to install to hardisk of the fedora core 11 live into VMware..which had failed..
wait till got time to do installation of the Desktop version instead..

fc11-install-to-hardsik.jpg

fc11-live-select-kebod.jpg

nearestcity.jpgfc11-partition.jpggot-encrypsystem.jpgencrypted.jpg
passphrase.jpg
installboot.jpghostanme.jpg

Get Free Email Updates!

Signup now and receive an email once I publish new content.

I will never give away, trade or sell your email address. You can unsubscribe at any time.

Like

Related Post

2 Responses

  1. namran says:

    4) Module parameters.
    ———————
    The following module parameters can be passed:

    mode=

    Possible values are 0 (round robin policy, default) and 1 (active backup
    policy), and 2 (XOR). See question 9 and the HA section for additional info.

    miimon=

    Use integer value for the frequency (in ms) of MII link monitoring. Zero value
    is default and means the link monitoring will be disabled. A good value is 100
    if you wish to use link monitoring. See HA section for additional info.

    downdelay=

    Use integer value for delaying disabling a link by this number (in ms) after
    the link failure has been detected. Must be a multiple of miimon. Default
    value is zero. See HA section for additional info.

    updelay=

    Use integer value for delaying enabling a link by this number (in ms) after
    the “link up” status has been detected. Must be a multiple of miimon. Default
    value is zero. See HA section for additional info.

    arp_interval=

    Use integer value for the frequency (in ms) of arp monitoring. Zero value
    is default and means the arp monitoring will be disabled. See HA section
    for additional info. This field is value in active_backup mode only.

    arp_ip_target=

    An ip address to use when arp_interval is > 0. This is the target of the
    arp request sent to determine the health of the link to the target.
    Specify this value in ddd.ddd.ddd.ddd format.

    If you need to configure several bonding devices, the driver must be loaded
    several times. I.e. for two bonding devices, your /etc/conf.modules must look
    like this:

    alias bond0 bonding
    alias bond1 bonding

    options bond0 miimon=100
    options bond1 -o bonding1 miimon=100

    Reply
  2. namran says:

    4) Module parameters.
    ———————
    The following module parameters can be passed:

    mode=

    Possible values are 0 (round robin policy, default) and 1 (active backup
    policy), and 2 (XOR). See question 9 and the HA section for additional info.

    miimon=

    Use integer value for the frequency (in ms) of MII link monitoring. Zero value
    is default and means the link monitoring will be disabled. A good value is 100
    if you wish to use link monitoring. See HA section for additional info.

    downdelay=

    Use integer value for delaying disabling a link by this number (in ms) after
    the link failure has been detected. Must be a multiple of miimon. Default
    value is zero. See HA section for additional info.

    updelay=

    Use integer value for delaying enabling a link by this number (in ms) after
    the “link up” status has been detected. Must be a multiple of miimon. Default
    value is zero. See HA section for additional info.

    arp_interval=

    Use integer value for the frequency (in ms) of arp monitoring. Zero value
    is default and means the arp monitoring will be disabled. See HA section
    for additional info. This field is value in active_backup mode only.

    arp_ip_target=

    An ip address to use when arp_interval is > 0. This is the target of the
    arp request sent to determine the health of the link to the target.
    Specify this value in ddd.ddd.ddd.ddd format.

    If you need to configure several bonding devices, the driver must be loaded
    several times. I.e. for two bonding devices, your /etc/conf.modules must look
    like this:

    alias bond0 bonding
    alias bond1 bonding

    options bond0 miimon=100
    options bond1 -o bonding1 miimon=100

    Reply

Anything to add?

X